It's time to start a new project, this time it will be a miniature car of my favorite rally driver - Juha Kankkunen.
Subaru was the last car that KKK won rallies and stood on the podium, so I decided to start at the end when it comes to building the Flying Finn models.
 
 
 
 
Of course, I will use the well-known and loved by modelers Tamiya's kit.

 

 

 

 

Let's see how the raw parts look like.

 

 

 

 

 

 

 

 

The model will be equipped with halogen lamps, I will use the lamps from the Subaru 2001 model.

 

 

 

 

To build a model in the Monte Carlo Rally 2000 specification I have to use a steering column with a gear lever from an Impreza 2001 model.

 

 

 

 

Additionaly I will use photo-etched set made by Hobby Design.

 

 

 

 

Another additional element needed to build such a model is carbon decals. The set made by C.B.COM does not have enough quality.
So I will use absolutely the minimum of that set and the rest will have to be taken from the Subaru 1998, 1999, 2001 kits.
In the photo below, the mentioned C.B.COM carbon decals and those from the Tamiya '99 set.
 
 
 
 
There will also be a lot of carbon and kevlar.
 
 
 
 
Color palette.
 
 
 
 
In general, there will be many modifications to get closer to the original 1:1. The body will be drilled, the radiator will be reworked, modeling rivets will appear, but I will write about all of that in on a regular basis in the next updates.
 
 
 
 
As always at the beginning, the seams and all unnecessary elements need to be removed from the model.
In the photos below, removed the turn signals, broached holes for rally pin stands and locks in the doors.
 
 
 
 
 
Removed pins on the hood and broached holes for screws fastening halogens.
 
 
 
 
Removed tailgate pins and drilled bumper for new fasteners.
 
 
 
 
Antennas bases removed.
 
 
 
 
Removed original bulbs and drilled covers for halogens in the bumper to put mounting bolts.
 
 
 
 
The next stage of work is the fitting of new bulbs and fixing screws.
 
 
 
 
 
Fitting the new turn signals.
 
 
 
 
The next stage is the filling with a putty of the rear spoiler gaps.
 
 
 
 
And sanding effects.
 
 
 
This way the model was ready to be painted with a primer. Here are the effects after the first visit to the paint booth.
 
 
 
 
 
 
 
After removal the radiator, the floor was also painted.
 
 
 
 
 
 
In today's update fittings of halogens and air intakes on the hood and roof of the model.
 
 
 
 
 
 
Taking this opportunity, I will say a few words about the issue that comes back very often when working on the Subaru S5 - it is about the front bumper and halogen lights. In the case of making the Prodrive Subaru S5 factory car from 1998 to 2000 (the first three rallies of the 2000 season), i.e. the last two evolutions of the S5, if we make a model without halogens then filling the bumper with the putty.
 
 
 
 
 
If you make car version for the night stages, do not fill up the bumper and halogens cover plates with the putty. These are covers screwed onto the bumper with the bolts. Picture from the Prodrive parts catalog.
 
 
 
 
 
 
 
Next work focused on reworking the roll cage. The Subaru in the '99 specification had additional connections between the cage and the windshield pillars. The roll cage itself also had more pipes, which I tried to reproduce.
 
 
 
 
 
Priming.
 
 
 
 
Another changes to the roll cage included the removal of two of the four side protectors.
The photo below before mods.
 
 
 
 
 
All the roll cage elements primed.
 
 
 
 
Another modified detail of the model is the trunk wall. Tamiya made a very nice rear shelf, while wall remained empty. So the drilled wall gained 24 rivets and two additional holes for fuel lines that will go to the model at later stages of work.
 
 
 
 
 
The model is ready for another visit to the spray booth.
 
 
 

Photo after visiting the spray booth.
 
 
 
 
 
 
 
 
 
 
 
 
The detail that caused me some problems was the panel line of the halogen housing.
It was difficult to shape it so that it was even, but finally it worked.
 
 
 
 
 
Thanks to the vigilance of my colleague Maciek (Madmax), it was possible to correct the error in the roll cage. I had to remove two reinforcements in its upper part. Here are the effects.
 
 
 
 
 
Now I would like to present a report on the work on Subaru rims, which were initially narrowed to make them look more credible after installing the tires.
 
 
 
 
 
Original rim size and after tapering.
 
 
 
 
Primer painting.
 
 
 
 
Target color and tire fitting.
 
 
 
 
 
Finally, a few photos from the suspension and rim fitting. All this to check whether the color of the rims will be appropriate.
I also had to measure how much I would like to lower the suspension.
 
 
 
 
 
I will start today's update where I finished recently, i.e. on the rims. Delicate screws wash, OZ decals, added air valves, rubbed off tires and here is the final effect.
 
 
 
 
 
The next stage of work is wrapping the model. It took me five days in total. It took a lot of time to figure out what decals to use to get the effect as close as possible to the Monte Carlo Rally 2000 specification. The decals on this model come from six different sets:

• Subaru Impreza 1999 (France Rally) Tamiya - 2 sheets
• Subaru impreza 1998 (Monte Carlo Rally) Tamiya
• Subaru Impreza 2001 (Monte Carlo Rally) Tamiya
• Ford Focus 2000 (Monte Carlo Rally) Revell
• Subaru Impreza 2000 (Monte Carlo Rally) C.B.COM
 
As for the product C.B.COM is generally not much useable. The pleiades are the wrong color and are wrongly scaled. There are funny mistakes in the subtitles themselves, such as the "alkon" advertisement written "alkom". Unfortunately, these decals are necessary to make this model correctly, which I will describe below.
 
 
 
 
Front bumper and hood:
• Prodrive at the radiator inlet - C.B.COM
• Alcon i Robin - Impreza 2001
• Pirelli, arrow and a pleiads on the grill and on the hood - Impreza 1999
 

Front wheel arches:
• Spot-On, Motul i Pirelli - Impreza 2001
• NGK - Impreza 1999

 

Side sections:
• White plastrons - Impreza 1999
• Plastrons from the Rally Monte Carlo - Ford Focus
• www.subaru-france.fr - C.B.COM
• Pleiads - Impreza 1999

 

I was not satisfied with the arrangement of pleiades around the door handles, so I decided to apply one more layer to them, so that's why I mentioned above that I used two sets. The effect is not perfect but decent.

 

Roof:
• White plastron - Impreza 1999
• LinelTEX - Impreza 1998
• Plastron Monte Carlo - Ford Focus 2000

 

Rear bumper, flap and spoiler:
• Advertisements on the sides of the spoiler - Impreza 1999
• Robin, pleiades and arrow - Impreza 1999
• Pirelli, Prodrive, www.subaru-france.fr - Impreza 2001

 
 

And here are the effects of wrapping.

 

 

 

 

 

 

 

 

 

 

Update 5 | 20.10.2020

In today's update, the clear paint and model polish effect. As standard, in my case, Tamiya products.

 

 

 

 

Here is the effect.

 

 

 

 

 

 

 

 

 

 

 

 

 
 

Author | Krzysztof Szpakowski

20 October 2020

Subaru Impreza WRC S5 | Tamiya 1:24